'Power mode' set to 'Best performance' and
'When plugged in, put my device to sleep after' set to 'Never'.
Despite this, the PC goes to sleep after a few minutes of being idle, which in turn kills RDP sessions which I do not want to happen.
There must be other settings somewhere which are overriding the 'Never' setting. Please help me understand what they are and how to change them.
Thank you and best regards
I've tried many methods to delete most recent Restore Point or any other point even via the cmd prompt *deleting shadow copies) and it doesn't work. I installed some software my IOBIT Uninstaller cannot find to uninstall and it is not in the list of Add/Remove programs but they are 368MB in size and installed in my pc and cannot llocate them. Only going back to my previous restore point would work and I try to do it but it does not work. PC boots up saying system restore failed most likely dur to active anti-virus software but I have my Bitdefender dissabled permanently when I did the restore point procedure.
Any ideas? Could Bootspeed interfere with restoring the pc at an earlier restore point?
I am using a ASUS N73S system with W10-64, Windows standard firewall and Kaspersky antivirus. All softwares are update and everything runs fine.
Working with IExplorer and Edge in parallel, suddenly the screen turns black and the system is blocked during 3 or 4 seconds, then the screen pops up again and the system reactivates in Without Error Mode. I have to reboot and the system reactivate in Normal Mode. This looks like a stability problem, but maybe a compatibility case between edge and ie.
Thank you to help me
Application Name: Ddfs32_400.exe
Application Version: 0.0.0.0
Application Timestamp: 602cd97f
Hang Signature: eff9
Hang Type: 134217728
OS Version: 6.3.9600.2.0.0.272.7
Locale ID: 1031
Additional Hang Signature 1: eff9e5103e62437273df6ec28305e96a
Additional Hang Signature 2: 4777
Additional Hang Signature 3: 477790f40c8afa87ecb7402697914cec
Additional Hang Signature 4: eff9
Additional Hang Signature 5: eff9e5103e62437273df6ec28305e96a
Additional Hang Signature 6: 4777
Additional Hang Signature 7: 477790f40c8afa87ecb7402697914cec
Wo steckt der Fehler? - Was soll ich überprüfen?
Buenos dias, tengo un problema con la aplicacion Auslogics Driver Update, ya solicite anteriormente me solucionen este problema, inclusive me solicitaron que reinstale el aplicativo, pero no se soluiciona este proble, por favor tengo que actualizar algunos drivers, pero se queda la PC congelada cuando va hacr la actualizacion de dichos driver, para constancia les envio fotos del problema.
I have your software in three computers as the license allows, but I can't find how to compare configuration between them, specially in the custom scan and clean for boostspeed. For example in one computer my login screen still shows the photo microsoft chooses, but on the other it doesn't. Maybe you have that in a config or xml file. It may be good to be able to compare.
Control Panel>Security and Maintenance>Reliability Monitor activated history is not available but for 1 day, no computer
reliability and problem history is shown in the graphic display. I have a lap top computer with the same setup as my desktop
and deleted BoostSpeed 12 from the laptop. The reliability and problem history started to show up on the chart. I conclude that there is something in the BoostSpeed software that is affecting this control panel issue. Got any fixes?
I purchased Disk Defrag, and later purchased Boostspeed. Under Boostspeed Disk Defrag I have always been able to Defrag & Optimize. I always run Defrag first (after disk cleanup), then I run Defrag & Optimize. I run these every Monday morning. I use about 19% of my 1T hard disk space. The only other programs are the automatically scheduled startup programs with staggered start delays up to 2 hours, so they should not significantly affect Defrag & Optimize.
Until 2 months ago, the longest Defrag & Optimze ran in 45 minutes or less. The maximum optimized files was about 45,000. When the Microsoft Windows update for June was implemented, the Defrag & Optimize ran over 3 hours. 2 days ago Defrag & Optimize ran for 5 hours 26 minutes with about 64,000 files optimized. The previous Defrag & Optimize was 6 days earlier.
I am a retired college educated computer professional (with all titles from programmer through analyst and manager) with over 40 years of experience. I have defragged computers for well over 25 years.
My question is "why is the Defrag & Optimize running so long and what can I do to speed it up?".
When using AusLogics BoostSpeed of any version (from version 5 to the latest) in the Microsoft Windows 10 Enterprise 2016 LTSB operating system, the reflection of available networks in the system tray disappears when you click on the network icon (both Wi-Fi and local). As well as a keyboard input indicator. Moreover, when uninstalling AusLogics BoostSpeed, this problem is not resolved. Which eliminates the use of AusLogics BoostSpeed on laptops with this system. How can this be fixed?