I have been using DiskDefrag for TEN years to successfully defrag my C: drive.

Starting last month Disk Defrag is not defraging my disk. I purchased the newer Disk Defrag 10 version and it performs exactly the same way.

Each time it runs it reportes processing a few dozen files and states Defragmentation complete, while the visual representation of the disk hardly changes at all - that is almost ALL the Red squares remain on the diagram.

Below is the image of my disk status after running DiskDefrag 20+ time; each time it reports "Defragmentation Complete"

Please contact me with a solution.

Can Auslogics BoostSteed be installed on a second computer?

Por favor quiero actualizar mi version a Pro

how offline activation future / BOOSTSPEED 12 PRO / key /

Здравствуйте! После выполнения глубокой очистки файлов перестало работать стандартное приложение Windows "Кино и ТВ". Исчез exe-файл - 0 байт. Прошу учесть при подготовке обновления BoostSpeed 12, а также подсказать - как востановить приложение "Кино и ТВ"?
С уважением,
Виктор Оплеснин

Hello,

Boostspeed runs every Sunday morning as part of scheduled maintenance I set-up. After it runs, I am prompted to re-enter my product key for Fences. I do this and Fences works fine. This is a nuicance though as I should not need to do this - the Fences registration is valid. Given the timing is consistent, I am assuming Boostpeed is causing this issue.

Several weeks ago, I did exempt my Anti-Virus software from scanning the Fences folder which contains the registration certificate. However, the prompts continue.

If Boostspeed is indeed causing this issue, is there a way to have it avoid removing/maninpulating the registration of this software so I don't have to re-enter the product code weekly?

Attached is the dialogue box that appears requesting to re-enter the product key.

Thanks,
Rich Sullivan

Bonjour,

Lorsque j'effectues une défragmentation de mon ssd avec l'option pour sdd, ils reste des carrées en rouge.
J'ai sélectionné dans les options 'tous les fichiers'.

Egalement l'indicateur ne se met pas a 0%

Cordialement
Denis Schmitt

Привет! У меня вопрос по программе Ausjogics BoostSpeed. Дело в том, что при каждом новом запуске загружается рекламное окно с предложением дополнить вашими прграммными продуктами мою систему. Это окно сжирает много ресурсов системы, что приводит к зависанию и потере времени, значительной потере. Как можно отключить данное окно? Ведь то , что меня интересовало, я уже приобрёл. Не хотелось бы получать разочарование от вашей продукции.
С уважением, Алексей.

Boostspeed 12 startet immer wenn Windows 7 geöffnet wird.
Wie kann man das verhindern?

There was no option for auslogics defragment so i chose a wrong category.My question is about defragment.Does defragmenting the hard disk HDD daily damage the hard disk or corrupt it ?

По чему произошла ошибка при регистрации

Where can I disable inside BoostSpeed 12 to not disable the Remote Desktop Service? Each time I reboot my PC I loose the ability to remote to my PC at the office because the service is disabled.

I just bought an additional laptop can I use my paid subscription and install it in my computer

Hi
I have used your software for years now.
I purchased new copies of Boostpeed and DriverUpdater
I don't have driverupdater on my computer just the web version
The webversion caused my windows not to reboot
I've had to re install everything
I would like to run driver updater but do not trust it without some sort of supervision
Can't go through this again
Registering all my purchases over again
Some still aren't working
Thank you
Thomas Horricks

How can I move "BootSpeed 12" to clean up my wifes computer?

see attached. This happens every time. Chrome, Brave will not allow. Edge gives error.

Buenos dias, tengo un problema con la aplicacion Auslogics Driver Update, ya solicite anteriormente me solucionen este problema, inclusive me solicitaron que reinstale el aplicativo, pero no se soluiciona este proble, por favor tengo que actualizar algunos drivers, pero se queda la PC congelada cuando va hacr la actualizacion de dichos driver, para constancia les envio fotos del problema.

Cant find the upate button to update

I have just installed a new external hard drive (G) and the drive is not displayed in the list of disks in Auslogics Disk defrag 10. Could you please advise me how to correct the issue.

Sorry but I did not know which sub category was appropriate

Where does display state the maximum number of user available with the product key assigned; and where does it show how many have been assigned; and where do they give the user name of the assigned